Stud Calculator

Count studs, plates, headers and cripples for a wall, with corners, T-intersections and every door and window accounted for.

The Stud Calculator runs entirely in your browser. Your wall dimensions stay on your device.

Built and maintained by Udit Agarwal

Open the Drywall Calculator

About Stud Calculator

A stud count is never just wall length divided by spacing. The wall needs a closing stud at the far end, three studs at every outside corner, two where a partition tees in, and each opening trades field studs for a king, jack and cripple assembly that adds more than it removes. Plates are simpler — one at the bottom and a doubled plate on top, three times the wall length — but they still have to be cut out of 16-foot stock, which is where the extra board comes from. This calculator does the whole takeoff, credits each opening the studs it displaces so an opening-heavy wall does not come out over-counted, and prints the layout marks you can pull straight off a tape.

Features

  • Field studs with the closing stud included
  • Three studs per corner and two per T-intersection
  • King, jack and cripple studs per opening, with cripples below windows
  • Field studs credited back where an opening displaces them
  • Plate linear feet and boards at 16 foot stock
  • Suggested header size for each opening width
  • Layout marks in inches from the end of the wall
  • Everything computes on your device

How to use the Stud Calculator

  1. Enter the wall length, height and stud spacing
  2. Add the corners and partition intersections in this run
  3. Add each door and window with its rough opening size
  4. Read the stud, plate, header and sheet counts

Example

Input

20 ft wall · 8 ft high · 16 in OC · 2 corners · 1 tee · one 3 × 6.75 ft door · 10% waste

Output

29 studs before waste → 32 to buy · 60 linear ft of plate (4 boards) · 1 header (2× 2x6) · 5 sheets per side

The door removes two field studs but adds two kings, two jacks and three cripples.

Common errors & troubleshooting

  • The count seems high for a short wall. — Corners and intersections dominate short walls: three studs per corner and two per tee add up fast. On a 8 foot wall with two corners, the corner studs outnumber the field studs.
  • Studs were left over after framing. — The calculator credits back field studs that fall inside an opening, but a real wall sometimes keeps one as a king. Small surpluses are normal and get used as cripples and blocking.
  • The plate count looks short. — Plates are three times the wall length — one bottom plate and two top plates — and top plate joints must be offset from the studs and lapped at corners, so buy one extra 16 foot board per long wall.

Frequently asked questions

How many studs do I need for a 20 foot wall?
At 16 inch centres a 20 foot wall takes 16 field studs, including the one that closes the end. Corners, intersections and openings are extra — two corners and one door typically push it to about 29.
Is 16 or 24 inch stud spacing better?
16 inch centres are the residential default and required in many load-bearing situations. 24 inch advanced framing uses about a third fewer studs and leaves more room for insulation, but needs thicker sheathing or drywall and careful load paths.
What are king, jack and cripple studs?
A king stud runs full height beside an opening. A jack stud is cut short and sits inside the king to carry the header. Cripples are the short studs that fill the space above the header, and below the sill on a window.
Why do corners need three studs?
Two studs form the corner itself and the third gives the intersecting wall's drywall something to fasten to. A three-stud corner is the traditional detail; a two-stud corner with drywall clips saves lumber and leaves room for insulation.
What size header does a 3 foot door need?
A doubled 2x6 covers a 3 foot opening in a single-storey bearing wall, and a 6 foot opening wants a doubled 2x12. Loads from a storey above, roofs or point loads change that, so check local span tables.

Related tools

Guides

More Construction tools

  • Roof Pitch Calculator — Convert pitch, angle, grade and slope factor, with rafter lengths and roof area.
  • Pipe Volume Calculator — Volume, water weight, fill time and flow velocity for any pipe run.
  • Siding Calculator — Squares, boxes, boards or panels of siding from wall sizes, gables and openings.
  • Concrete Calculator — Estimate concrete volume and bags for slabs, footings and columns.
  • BTU Calculator — Estimate the BTU capacity needed to heat or cool a room.
  • Square Footage Calculator — Calculate area in square feet or meters for rooms and projects, with cost.
  • Stair Calculator — Calculate stair rise, run, number of steps and stringer length for a staircase.
  • Roofing Calculator — Estimate roof area, squares and shingle bundles from footprint and pitch.
  • Tile Calculator — Calculate how many tiles and boxes you need for a floor or wall.
  • Mulch Calculator — Estimate mulch volume in cubic yards and bags for a bed and depth.
  • Gravel Calculator — Estimate gravel volume and weight in tons for an area and depth.
  • Paint Calculator — Work out how much paint a room needs from its size, coats, doors and windows.

See all Construction tools (22) · All tools